View FTLF1319F1GTL_4427494.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Finisar
Product Specification
2 Gigabit RoHS Compliant Long-Wavelength 2x5 Pin SFF Transceiver
FTLF1319F1xTL
PRODUCT FEATURES * * * * * * * * * * * Up to 2.125Gb/s bi-directional data links Standard 2x5 pin SFF footprint (MSA compliant) 1310nm Fabry-Perot laser transmitter Duplex LC connector RoHS compliant and Lead Free Very low jitter Up to 10 km on 9/125m SMF Metal enclosure, for lower EMI Single 3.3V power supply Low power dissipation <700mW Industrial operating temperature range: -40C to 85C APPLICATIONS * * 1.25 Gb/s 1000Base-LX Ethernet Dual Rate 1.063 / 2.125 Gb/s Fibre Channel
Finisar's FTLF1319F1xTL Small Form Factor (SFF) transceivers comply with the 2x5 standard package defined by the Small Form Factor Multi-Sourcing Agreement (MSA)1. They are simultaneously compatible with Gigabit Ethernet as specified in IEEE Draft P802.3z/D5.02 and Fibre Channel FC-PH, PH2, PH33 and FC-PI-2 10.04. They are RoHS compliant and lead-free per Directive 2002/95/EC5 and Finisar Appl. Note AN-2038. PRODUCT SELECTION
FTLF1319F1xTL
x G M K H
2 Grounding Pins, Short EMI shield 6 Grounding Pins, Short EMI shield 2 Grounding Pins, Long EMI shield 6 Grounding Pins, Long EMI shield
(c) Finisar Corporation March 30, 2006 Rev. D
Page 1
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
I.
Pin Descriptions
Pin MS 1 2 3 4 5 6 7 8 9 10 Symbol MS VEER VCCR SD RDRD+ VCCT VEET TDIS TD+ TDName/Description Mounting Studs are for mechanical attachment. Chassis ground is internally isolated from circuit ground. Connection to chassis ground is recommended. Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Signal Detect. Logic 1 indicates normal operation. Receiver Inverted DATA out. AC Coupled. Receiver Non-inverted DATA out. AC Coupled Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Disable Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled.
MS
Logic Family NA NA NA LVTTL See Rx spec. See Rx spec. NA NA LVTTL See Tx spec See Tx spec.
10 9 8 7 6
TOP VIEW
12345
MS
II.
Absolute Maximum Ratings
Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Lead Soldering Temperature/Time Notes: 1. Non condensing.
Symbol Vcc TS TA RH
Min 0.5 -40 -40 0
Typ
Max 5.0 85 85 85 260/10
Unit V C C % C/s
Ref.
1
(c) Finisar Corporation March 30, 2006 Rev. D
Page 2
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
III.
Electrical Characteristics (TA = -40 to 85 C, VCC = 3.0 to 3.60 Volts)
Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise time Data output fall time Signal Detect Normal Signal Detect Fault Power Supply Rejection Deterministic Jitter Contribution (p-p) Total Jitter Contribution (p-p) Notes: 1. 2. 3. 4. 5. 6. 7. 8.
Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr tf VSD norm VSD fault PSR RX DJ RX TJ
Min 3.00
Typ
Max 3.60 300
Unit V mA mV V V us mV ps ps V V mVpp ps ps
Ref.
100 250 Vcc - 1.3 Vee 1200 Vcc Vee+ 0.8 10 800 175 175 Vcc Vee+0.5 50 120
1
2
300 100 100 Vcc - 0.5 Vee 100
3 4 4 5 5 6 7 8
AC coupled. Or open circuit. Into 100 differential termination. 20 - 80 % Signal detect is LVTTL. Logic 1 indicates normal operation; logic 0 indicates no signal detected. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ. If measured with TJ-free data input signal. In actual application, output TJ will be given by:
TJ OUT = DJ IN + DJ +
(TJ IN
- DJ IN ) + (TJ - DJ )
2
2
(c) Finisar Corporation March 30, 2006 Rev. D
Page 3
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
IV.
Optical Characteristics (TA = -40 to 85 C, VCC = 3.0 to 3.60 Volts)
Parameter Transmitter Output Opt. Power Optical Wavelength Spectral Width Optical Modulation Amplitude Optical Rise/Fall Time RIN Deterministic Jitter Contribution Total Jitter Contribution Extinction Ratio Receiver Receiver Sensitivity = 1.06 Gb/s Receiver Sensitivity = 2.125 Gb/s Receiver Sensitivity = 1.25 Gb/s Stressed RX sens. =1.0625 Gb/s Stressed RX sens. =2.125 Gb/s Stressed RX sens. =1.25 Gb/s Average Received Power Receiver Elec. 3 dB cutoff freq. Optical Center Wavelength Return Loss Signal Detect Assert Signal Detect De-Assert Signal Detect Hysteresis
Symbol POUT OMA tr/ tf TX DJ TX TJ ER RxSENS RxSENS RxSENS
Min -9.5 1270 174
Typ
Max -3 1355 3
Unit dBm nm nm W ps dB/Hz ps ps
Ref. 1 2 2 2,3 4 5 6
100 20 <65 9
160 -120 56.5 119
-22 -21 -22 0.055 0.096 -18 -14.5 0 1500 1600 -19
RxMAX C PA PD P A - PD 1270 12 -30 0.5 -23 -25
dBm dBm dBm mW mW dBm dBm MHz nm dB dBm dBm dB
7, 8 7, 8 7, 8
Notes: 1. Class 1 Laser Safety per FDA/CDRH and IEC-825-1 regulations. 2. Also specificied to meet curves in FC-PI-2 10.0 Figures 18 and 19, which allow trade-off between wavelength, spectral width and OMA. 3. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 4. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye mask when filtered. 5. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ. 6. If measured with TJ-free data input signal. In actual application, output TJ will be given by:
TJ OUT = DJ IN + DJ +
7. 8.
(TJ IN
- DJ IN ) + (TJ - DJ )
2
2
Measured with conformance signals defined in FC-PI-2 10.0 specifications. Measured with PRBS 27-1 at 10-12 BER.
(c) Finisar Corporation March 30, 2006 Rev. D
Page 4
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
V.
General Specifications
Parameter Symbol BR BER LMAX1 LMAX1 Min Typ 1.0625, 1.25, 2.125 10 10 Max Units Gb/sec Ref. 1 2 3 4
Data Rate Bit Error Rate Max. Supported Link Length on 9/125m SMF @ 2x Fibre Channel Max. Supported Link Length on 9/125m SMF @ Gigabit Ethernet
10-12 km km
Notes: 1. Gigabit Ethernet and 1x, 2x Fibre Channel compatible, per IEEE 802.3 and FC-PI-2 10.0, respectively. Typical maximum data rate extends to 2.5Gb/s. 2. Tested with PRBS 27-1 test pattern. 3. Dispersion limited per FC-PI-2 10.0 4. Attenuation of 0.55 dB/km is used for the link length calculations. Distances are indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application.
VI.
Environmental Specifications
Finisar SFF transceivers have an extended operating temperature range from -40C to +85C case temperature.
Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min -40 -40 Typ Max 85 85 Units C C Ref.
VII.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TUV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
(c) Finisar Corporation March 30, 2006 Rev. D
Page 5
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
VIII. Mechanical Specifications Finisar's Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA).
FTLF1319F1GTL
(c) Finisar Corporation March 30, 2006 Rev. D
Page 6
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
FTLF1319F1MTL
(c) Finisar Corporation March 30, 2006 Rev. D
Page 7
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
FTLF1319F1HTL
(c) Finisar Corporation March 30, 2006 Rev. D
Page 8
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
IX.
PCB Layout and Bezel Recommendations
Minimum Recommended Pitch is 0.600"
(c) Finisar Corporation March 30, 2006 Rev. D Page 9
FTLF1319F1xTL 2x5 Pin SFF Product Specification - March 2006
Finisar
X.
References
1. Small Form Factor (SFF) Transceiver Multi-source Agreement (MSA). January 6, 1998. 2. "IEEE Draft P802.3z/D5.0 `Media Access Control (MAC) Parameters, Physical Layer, Repeater and Management Parameters for 1000Mb/s Operation'". IEEE Standards Department, 1998. 3. "Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)". American National Standard for Information Systems. 4. "Fibre Channel Draft Physical Interface Specification (FC-PI-2 10.0)". American National Standard for Information Systems.
5. Directive 2002/95/EC of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment." January 27, 2003.
XI.
For More Information
Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. (408) 548-1000 Fax (408) 541-6138 sales@finisar.com www.finisar.com
(c) Finisar Corporation March 30, 2006 Rev. D
Page 10

▲Up To Search▲

Price & Availability of FTLF1319F1GTL

	To Download FTLF1319F1GTL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .